News

Pipeline construction and maintenance often occur in or near environmentally sensitive areas — wetlands, riparian zones, protected habitats, and water supply watersheds. Coating application in these environments requires careful planning and execution to prevent chemical contamination, minimize habitat disturbance, and comply with environmental permit conditions.

VOC Emissions Management

Many pipeline coating materials historically contained significant levels of volatile organic compounds (VOCs) that contribute to air quality degradation. Modern high-solids and 100% solids polyurea formulations have virtually eliminated VOC emissions from the coating application process, providing both environmental benefits and improved worker health outcomes. Solvent-based primers should be substituted with waterborne or solvent-free alternatives wherever possible.

Spill Prevention During Application

Plural-component spray equipment must be positioned and operated to prevent spills of isocyanate components — hazardous materials requiring secondary containment and spill response procedures. Drip pans, lined work areas, and trained equipment operators are minimum requirements for any application near water bodies or sensitive soils.

Green Certification Programs

Pipeline operators increasingly require environmental certifications from their coating contractors, including ISO 14001 Environmental Management System certification and adherence to environmental best practice guidelines published by organizations such as the Interstate Natural Gas Association of America (INGAA). Our resources section includes environmental compliance templates and contractor qualification questionnaires.

Pipelines operating at temperatures above 200°F — including those carrying heavy crude, steam-assisted gravity drainage (SAGD) output, and geothermal fluids — present challenges that conventional organic coating systems cannot reliably address. Thermal spray coatings and high-temperature inorganic coating systems fill this critical gap in the pipeline coating toolkit.

Thermal Spray Technologies

Thermal spray processes including arc spray, flame spray, and high-velocity oxyfuel (HVOF) deposit metallic or ceramic coatings by projecting molten particles onto a prepared substrate. Zinc and aluminum thermal spray coatings provide galvanic protection similar to hot-dip galvanizing, while tungsten carbide HVOF coatings offer exceptional erosion resistance for high-velocity slurry service.

High-Temperature Organic Systems

Modified silicone, phenolic epoxy, and high-solids baked amine coatings extend organic coating service temperatures to 400–600°F for above-grade piping. These systems sacrifice some of the mechanical flexibility of polyurea in exchange for superior temperature resistance, making them complementary technologies rather than direct competitors.

Hybrid Solutions for SAGD Pipelines

SAGD gathering lines present a uniquely challenging environment: high temperature near the wellhead, thermal cycling as production fluctuates, and aggressive soil chemistry in many Canadian oil sands formations. Innovative operators are combining aluminum thermal spray for temperature resistance with polyurea topcoats for environmental sealing, creating hybrid systems that perform exceptionally well across the full operating envelope.

The Spring Pipeline Coatings Summit brought together over 340 industry professionals from 28 countries for three days of technical sessions, panel discussions, and networking at the George R. Brown Convention Center in Houston. The event set a new attendance record and generated significant discussion around emerging coating technologies and evolving regulatory requirements.

Day One: Advances in Spray Polyurea Technology

The opening keynote by Dr. Sarah Whitfield of the Pipeline Research Council International (PRCI) provided a comprehensive review of five-year field performance data on spray polyurea coatings across 23 pipeline systems. Key findings included average service lives exceeding initial design life by 15 years and cathodic disbondment rates 60% lower than comparable epoxy systems under identical CP conditions.

Day Two: Regulatory Update Session

The day two regulatory panel featured representatives from PHMSA, Transport Canada, and the EU Pipeline Safety Coordination Group. Discussion centered on the pending PHMSA coating standards update and its implications for operators running legacy coating systems on aging infrastructure. Panelists emphasized the 2–3 year lead time needed for operators to qualify new coating systems before regulatory deadlines.

Day Three: Workshops and Networking

The final day featured hands-on workshops on plural-component spray equipment maintenance, holiday testing procedures, and cathodic protection troubleshooting. The evening networking dinner drew the largest turnout in the event’s history, with strong interest in the organization’s new regional chapter program.

All presentation materials from the Summit are available to members in our resources library. Registration for the Fall Technical Conference is now open.

Two of the most widely discussed coating and lining options for new pipeline construction are high-density polyethylene (HDPE) outer wrap/sleeve systems and spray-applied polyurea coatings. Each has a dedicated following in the industry, and the optimal choice depends heavily on application environment, installation method, and lifecycle cost objectives.

HDPE Coating Systems

Factory-applied HDPE coatings — typically three-layer systems with an FBE primer, adhesive, and HDPE topcoat — provide exceptional mechanical protection during installation, particularly for directional drilling and rocky trench conditions. The HDPE layer’s abrasion resistance is unmatched by any spray-applied alternative at standard thicknesses.

Spray Polyurea Advantages

Spray polyurea’s advantages emerge most clearly in field joint coating, irregular geometries, and rehabilitation scenarios. A skilled applicator can coat a 40-inch diameter field joint in under 10 minutes, achieving uniform thickness over the weld bead and adjacent areas that factory-applied wraps cannot access. Polyurea also offers superior elongation, accommodating soil movement and thermal cycling without cracking or delamination.

A Hybrid Approach

Many experienced pipeline engineers specify a hybrid approach: factory-applied three-layer polyethylene for mainline pipe with spray polyurea for all field joints and special sections. This combination leverages the manufacturing efficiency of factory coating with the field adaptability of polyurea, delivering the best performance profile at a competitive lifecycle cost.

For more technical comparisons, visit our technical library or join the discussion in our Materials and Coatings Working Group.

Internal pipeline liners serve a dual purpose: they protect the pipe wall from chemical attack and erosion by transported fluids, and they reduce surface roughness to improve flow efficiency. In the oil and gas industry, even a modest improvement in flow coefficient translates to millions of dollars in pumping energy savings across a large network.

Types of Internal Liners

The primary categories of internal pipeline lining systems include spray-applied liquid coatings, cured-in-place pipe (CIPP) liners, and mechanical slip liners. Each is suited to different pipe diameters, operating conditions, and rehabilitation scenarios.

Spray-Applied Internal Coatings

For large-diameter pipelines (typically 12 inches and above), robotic spray systems apply polyurea or epoxy liners from the interior, achieving consistent film thickness across complex geometries including bends and T-connections. Modern robotic applicators can line up to 1,500 feet of pipe per day with laser-guided thickness monitoring.

Drag Reduction Liners

Specialized smooth-surface epoxy liners reduce the Manning roughness coefficient of steel pipe from 0.013 to as low as 0.009, delivering flow efficiency improvements of 15–25% compared to unlined corroded pipe. When combined with external polyurea protection, a fully lined pipeline represents the gold standard in long-term asset management.

Quality Control and Inspection

Internal coating quality is verified through CCTV inspection, laser profilometry, and random coupon pull tests. AWWA C210 and API 5L provide the foundational standards for internal lining of steel pipelines. Our resources library includes detailed QC procedure guides for internal application projects.

Polyaspartic coatings — a subclass of polyurea systems using aspartic acid ester technology — have carved out a significant niche in pipeline rehabilitation and maintenance applications. Their combination of rapid cure, UV stability, and excellent mechanical properties addresses limitations that have historically made field-applied coatings a compromise solution.

What Makes Polyaspartic Different

Traditional aliphatic polyurethane topcoats offer UV stability but require extended cure times that are impractical in pipeline maintenance scenarios. Polyaspartics achieve aliphatic UV performance with cure times approaching those of aromatic polyurea — typically 2–4 hours to full service versus 24–48 hours for standard polyurethane systems. This dramatically reduces pipeline downtime during above-ground rehabilitation projects.

Advantages for Pipeline Rehabilitation

• Single-coat application to 20+ mils DFT, reducing labor costs
• High gloss, color-stable finish suitable for above-grade facilities
• Excellent resistance to splash zone immersion
• Flexible formulations available for thermal cycling environments
• Compatible with most existing coating systems as a topcoat

Application Considerations

Polyaspartic systems can be applied by airless spray, conventional spray, or brush/roller for small areas. Plural-component systems at 2:1 or 1:1 mix ratios are most common. Because the amine reactivity of polyaspartic resins is lower than that of standard amine curatives, pot life can range from 30 minutes to several hours depending on formulation — a significant practical advantage over spray polyurea in areas requiring careful workmanship.

For more on the full spectrum of coating options for pipeline rehabilitation projects, see our comprehensive coating comparison guide and browse our network of certified applicators experienced in rehabilitation work.